# Sketch Set - assign model

**URL:** <https://forum.itascainternational.com/t/sketch-set-assign-model/2020>\
**Category:** FLAC3D\
**Created:** [April 3, 2025, 6:20am UTC](https://forum.itascainternational.com/t/sketch-set-assign-model/2020 "2025-04-03T06:20:02Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![sowmyaramanis](https://avatars.discourse-cdn.com/v4/letter/s/839c29/32.png) [@sowmyaramanis](https://forum.itascainternational.com/u/sowmyaramanis)\
**Post date:** [April 3, 2025, 6:20am UTC](https://forum.itascainternational.com/t/sketch-set-assign-model/2020/1 "2025-04-03T06:20:02Z")

</div>

I have created the required model using the sketch set and later renamed the labels for my convenience. I am not able to apply the cmodel or any properties to the groups through the commands I give.

For eg: I have named one of the columns as “col1” Buty when I am trying to assign a cmodel to it, it says that it gets applied to 0 zones.

How should I specify these groups ?

I have attached the reference pictures

 ![image](https://canada1.discourse-cdn.com/flex031/uploads/itasca/original/2X/3/3db3b92b46a931c3881f551b893f99e2844379bf.png)  
 ![image](https://canada1.discourse-cdn.com/flex031/uploads/itasca/original/2X/7/7a644386b312e22ea63e20c18cb3ce227c261cbf.png)

---

<div class="post-metadata">

**Author:** ![apyatigorets](https://avatars.discourse-cdn.com/v4/letter/a/58f4c7/32.png) [@apyatigorets](https://forum.itascainternational.com/u/apyatigorets)\
**Post date:** [April 4, 2025, 12:24am UTC](https://forum.itascainternational.com/t/sketch-set-assign-model/2020/2 "2025-04-04T00:24:09Z")

</div>

Even though all the groups appear fine based on the images you provided, I find it somewhat strange that no Slot is listed for groups `col1`, `sand`, and `soil`, however slots are listed for other groups (e.g., `Block`, `Segment`). So I have a suspicion that group renaming/assignment was not done properly (or potentially you discovered some bug).

Could you share the commands you used for groups renaming/assignment ?

---

<div class="post-metadata">

**Author:** ![sowmyaramanis](https://avatars.discourse-cdn.com/v4/letter/s/839c29/32.png) [@sowmyaramanis](https://forum.itascainternational.com/u/sowmyaramanis)\
**Post date:** [April 4, 2025, 3:55am UTC](https://forum.itascainternational.com/t/sketch-set-assign-model/2020/3 "2025-04-04T03:55:43Z")

</div>

Thank you for your response sir. But I figured out a way to apply the model and its properties.

Instead using the commands, I directly assigned using the model pane and it worked.

---

<div class="post-metadata">

**Author:** ![apyatigorets](https://avatars.discourse-cdn.com/v4/letter/a/58f4c7/32.png) [@apyatigorets](https://forum.itascainternational.com/u/apyatigorets)\
**Post date:** [April 4, 2025, 2:42pm UTC](https://forum.itascainternational.com/t/sketch-set-assign-model/2020/4 "2025-04-04T14:42:40Z")

</div>

I am glad you were able to find a solution! It may not be very obvious until one digs through it, but there a are quite a few things people can do in the ModelPane with model setup.

---

<div class="post-metadata">

**Author:** ![sowmyaramanis](https://avatars.discourse-cdn.com/v4/letter/s/839c29/32.png) [@sowmyaramanis](https://forum.itascainternational.com/u/sowmyaramanis)\
**Post date:** [April 16, 2025, 6:57pm UTC](https://forum.itascainternational.com/t/sketch-set-assign-model/2020/5 "2025-04-16T18:57:44Z")

</div>

I also wanted to know that the geometry that is created using the sketchset can be saved?  
because every single time when I have to run the model for different parametric values, I has to create it again and again.

---

<div class="post-metadata">

**Author:** ![msepu](https://avatars.discourse-cdn.com/v4/letter/m/b9e5f3/32.png) [@msepu](https://forum.itascainternational.com/u/msepu)\
**Post date:** [April 17, 2025, 2:06pm UTC](https://forum.itascainternational.com/t/sketch-set-assign-model/2020/6 "2025-04-17T14:06:55Z")

</div>

after creating the geometry, you have to save that state :  
“model save ‘geometry.sav’”

and after, when you want to try other parametrics values, you should start from that saved state:

"Model rest ‘geometry.sav’ "
